智能灯 arduino总是报错
我按照这篇文档做的《30分钟用arduino开发属于自己智能灯》，库文件都已经放在libiaries里面了，但是还是报错我修改后的代码是这个
#include <Gizwits.h>#include <Wire.h>#include <SoftwareSerial.h>#include <ChainableLED.h>
SoftwareSerial mySerial(A2, A3); // A2 -> RX, A3 -> TX
Gizwits myGizwits;
#define KEY1 6#define KEY2 7#define KEY1_SHORT_PRESS1#define KEY1_LONG_PRESS 2#define KEY2_SHORT_PRESS4#define KEY2_LONG_PRESS 8#define NO_KEY 0#define KEY_LONG_TIMER 3unsigned long Last_KeyTime = 0;uint8_t Set_LedStatus = 0;
ChainableLED leds(A5,A4,1);
void LED_RGB_Control(byte red,byte green,byte blue){leds.setColorRGB(0,red,green,blue);}
unsigned long gokit_time_s(void){return millis() / 1000;}
char gokit_key1down(void){unsigned long keep_time = 0;if (digitalRead(KEY1) == LOW){ delay(100); if (digitalRead(KEY1) == LOW) { keep_time = gokit_time_s(); while (digitalRead(KEY1) == LOW) { if ((gokit_time_s() - keep_time) > KEY_LONG_TIMER) { Last_KeyTime = gokit_time_s(); return KEY1_LONG_PRESS; } } //until open the key
if ((gokit_time_s() - Last_KeyTime) > KEY_LONG_TIMER) { return KEY1_SHORT_PRESS; } return 0; } return 0;}return 0;}
char gokit_key2down(void){int unsigned long keep_time = 0;if (digitalRead(KEY2) == LOW){ delay(100); if (digitalRead(KEY2) == LOW) { keep_time = gokit_time_s(); while (digitalRead(KEY2) == LOW) //until open the key {
if ((gokit_time_s() - keep_time) > KEY_LONG_TIMER) { Last_KeyTime = gokit_time_s(); return KEY2_LONG_PRESS; } }
if ((gokit_time_s() - Last_KeyTime) > KEY_LONG_TIMER) { return KEY2_SHORT_PRESS; } return 0; } return 0;}return 0;}
char gokit_keydown(void){char ret = 0;ret |= gokit_key2down();ret |= gokit_key1down();return ret;
}
/*** KEY_Handle * @param none* @return none*/void KEY_Handle(void){/*Press for over than 3 second is Long Press*/switch (gokit_keydown()){ case KEY1_SHORT_PRESS: mySerial.println(F("KEY1_SHORT_PRESS , Production Test Mode ")); myGizwits.setBindMode(WIFI_PRODUCTION_TEST); break; case KEY1_LONG_PRESS: mySerial.println(F("KEY1_LONG_PRESS ,Wifi Reset")); myGizwits.setBindMode(WIFI_RESET_MODE); break; case KEY2_SHORT_PRESS: mySerial.println(F("KEY2_SHORT_PRESS Soft AP mode")); myGizwits.setBindMode(WIFI_SOFTAP_MODE); //Soft AP mode break; case KEY2_LONG_PRESS: mySerial.println(F("KEY2_LONG_PRESS ,AirLink mode")); myGizwits.setBindMode(WIFI_AIRLINK_MODE); //AirLink mode break; default: break;}}
/*** Serial Init , Gizwits Init* @param none* @return none*/void setup() {// put your setup code here, to run once:mySerial.begin(115200);leds.init();digitalWrite(A0,HIGH);pinMode(KEY1, INPUT_PULLUP);pinMode(KEY2, INPUT_PULLUP);pinMode(5,OUTPUT);
myGizwits.begin();
mySerial.println("GoKit initOK \n");}
/*** Wifi status printf* @param none* @return none*/void wifiStatusHandle(){if(myGizwits.wifiHasBeenSet(WIFI_SOFTAP)){ mySerial.println(F("WIFI_SOFTAP!"));}if(myGizwits.wifiHasBeenSet(WIFI_AIRLINK)){ mySerial.println(F("WIFI_AIRLINK!"));}if(myGizwits.wifiHasBeenSet(WIFI_STATION)){ mySerial.println(F("WIFI_STATION!"));}if(myGizwits.wifiHasBeenSet(WIFI_CON_ROUTER)){ mySerial.println(F("WIFI_CON_ROUTER!"));}if(myGizwits.wifiHasBeenSet(WIFI_DISCON_ROUTER)){ mySerial.println(F("WIFI_DISCON_ROUTER!"));}if(myGizwits.wifiHasBeenSet(WIFI_CON_M2M)){ mySerial.println(F("WIFI_CON_M2M!"));}if(myGizwits.wifiHasBeenSet(WIFI_DISCON_M2M)){ mySerial.println(F("WIFI_DISCON_M2M!"));}}
/*** Arduino loop * @param none* @return none*/void loop() {KEY_Handle();//key handle , network configurewifiStatusHandle();//WIFI Status Handle
bool varR_LED = 0;if(myGizwits.hasBeenSet(EVENT_LED)){ myGizwits.read(EVENT_LED,&varR_LED);//Address for storing data if (varR_LED == 1) { LED_RGB_Control(200,0,0); } else { LED_RGB_Control(0,0,0); }
} myGizwits.process();}
报错的信息是这个
Arduino:1.8.4 (Windows 8.1), 开发板："Arduino/Genuino Uno"
In file included from C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.c:16:0:
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.c: In function 'returnNtp2Wt':
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.h:67:23: warning: integer overflow in expression [-Woverflow]
#define DAY_SEC (24*60*60)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.c:246:21: note: in expansion of macro 'DAY_SEC'
if(utc >= x*DAY_SEC)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.h:67:23: warning: integer overflow in expression [-Woverflow]
#define DAY_SEC (24*60*60)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.c:248:22: note: in expansion of macro 'DAY_SEC'
utc -= x*DAY_SEC;
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.h:67:23: warning: integer overflow in expression [-Woverflow]
#define DAY_SEC (24*60*60)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.c:262:27: note: in expansion of macro 'DAY_SEC'
if(utc >= mons*DAY_SEC)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.h:67:23: warning: integer overflow in expression [-Woverflow]
#define DAY_SEC (24*60*60)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.c:264:28: note: in expansion of macro 'DAY_SEC'
utc -= mons*DAY_SEC;
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.h:67:23: warning: integer overflow in expression [-Woverflow]
#define DAY_SEC (24*60*60)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.c:277:19: note: in expansion of macro 'DAY_SEC'
if(utc >= DAY_SEC)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.h:67:23: warning: integer overflow in expression [-Woverflow]
#define DAY_SEC (24*60*60)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.c:279:20: note: in expansion of macro 'DAY_SEC'
utc -= DAY_SEC;
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\gizwits_protocol.c: In function 'gizwitsHandle':
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\gizwits_protocol.c:1243:13: warning: implicit declaration of function 'gizwitsEventProcess' [-Wimplicit-function-declaration]
gizwitsEventProcess(&gizwitsProtocol.issuedProcessEvent, (uint8_t *)&gizwitsProtocol.gizCurrentDataPoint, sizeof(dataPoint_t));
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:21:13: error: variable or field 'rb_new' declared void
void rb_new(RingBuffer* rb)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:21:13: error: 'RingBuffer' was not declared in this scope
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:21:25: error: 'rb' was not declared in this scope
void rb_new(RingBuffer* rb)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:34:15: error: variable or field 'rb_free' declared void
voidrb_free(RingBuffer *rb)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:34:15: error: 'RingBuffer' was not declared in this scope
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:34:27: error: 'rb' was not declared in this scope
voidrb_free(RingBuffer *rb)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:39:24: error: 'RingBuffer' was not declared in this scope
size_t rb_capacity(RingBuffer *rb)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:39:36: error: 'rb' was not declared in this scope
size_t rb_capacity(RingBuffer *rb)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:40:1: error: expected ',' or ';' before '{' token
{
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:44:24: error: 'RingBuffer' was not declared in this scope
size_t rb_can_read(RingBuffer *rb)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:44:36: error: 'rb' was not declared in this scope
size_t rb_can_read(RingBuffer *rb)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:45:1: error: expected ',' or ';' before '{' token
{
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:51:25: error: 'RingBuffer' was not declared in this scope
size_t rb_can_write(RingBuffer *rb)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:51:37: error: 'rb' was not declared in this scope
size_t rb_can_write(RingBuffer *rb)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:52:1: error: expected ',' or ';' before '{' token
{
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:57:20: error: 'RingBuffer' was not declared in this scope
size_t rb_read(RingBuffer *rb, void *data, size_t count)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:57:32: error: 'rb' was not declared in this scope
size_t rb_read(RingBuffer *rb, void *data, size_t count)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:57:36: error: expected primary-expression before 'void'
size_t rb_read(RingBuffer *rb, void *data, size_t count)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:57:55: error: expected primary-expression before 'count'
size_t rb_read(RingBuffer *rb, void *data, size_t count)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:57:60: warning: expression list treated as compound expression in initializer [-fpermissive]
size_t rb_read(RingBuffer *rb, void *data, size_t count)
^
C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:58:1: error: expected ',' or ';' before '{' token
{
^
exit status 1为开发板 Arduino/Genuino Uno 编译时出错。
在文件 -> 首选项开启“编译过程中显示详细输出”选项这份报告会包含更多信息。
感觉不该有问题才对啊求前辈们指点
页:
[1]