机智云»社区首页 › 开源项目及赛事 › Arduino IoT开发 › 自动代码生成arduino全系列移植，Arduino联网就那么简单 ...

自动代码生成arduino全系列移植，Arduino联网就那么简单

查看数: 220414 | 评论数: 264 | 收藏 12

关灯 | 提示：支持键盘翻页<-左右->

帖子模式

Suaig

发布时间: 2017-3-31 16:47

正文摘要:

replyreload += ',' + 21854; 本帖最后由 Suaig 于 2017-5-3 23:59 编辑手把手把机智云移植到任意arduino uno R3/2560的步骤（不带LOG）换句话说，你的手里闲置的Arduino uno R3能具备联网功能了。而且还能体验 ...

nan336523 发表于 2017-4-29 21:20:13

我使用的楼主的源程序为什么会提示VALUE_VOLT这个未**呢？？

热爱生活 发表于 2017-4-12 21:08:07

Suaig 发表于 2017-4-11 15:49
邮箱

simpleTry.zip (28.08 KB, 下载次数: 105)

/*****************************************
Name: Gizwits + ArduinoUnoWiFi Library
Author: <A href="mailto:tli@gizwits.com">tli@gizwits.com</A> / <A href="mailto:bing@arduino.org.cn">bing@arduino.org.cn</A>
Version: V1.0
Init: 2016-12-23
Modify: 2016-12-23
*******************************************/
//只有一个buer开关数据点
#include "Gizwits.h"
#include <Wire.h>
Gizwits myGizwits;
void setup() {
// put your setup code here, to run once:
Serial.begin(9600);
pinMode(7,INPUT_PULLUP);
pinMode(8,INPUT_PULLUP);
pinMode(9,INPUT_PULLUP);
digitalWrite(9,HIGH);//9号数字接口连接led灯测试是否接收到数据
delay(500);
digitalWrite(9,LOW);
delay(500);
digitalWrite(9,HIGH);
delay(500);
digitalWrite(9,LOW);
myGizwits.begin();
}
void loop() {
//Configure network
//if(XXX) //Trigger Condition
//myGizwits.setBindMode(0x02); //0x01:Enter AP Mode;0x02:Enter Airlink Mode
/*
bool varR_buer = 0;
if(myGizwits.hasBeenSet(EVENT_BUER))
{
myGizwits.read(EVENT_BUER,&varR_buer);//Address for storing data
}
//binary datapoint handle
*/
//Configure network
if(digitalRead(7) == LOW) //Trigger Condition
{
delay(10);
while(digitalRead(7) == LOW);
myGizwits.setBindMode(WIFI_AIRLINK_MODE); //0x01:Enter AP Mode;0x02:Enter Airlink Mode
// Serial.println("START_AIRLINK");
}
if(digitalRead(8) == LOW) //Trigger Condition
{
delay(10);
while(digitalRead(8) == LOW);
myGizwits.setBindMode(WIFI_RESET_MODE); //0x01:Enter AP Mode;0x02:Enter Airlink Mode
//Serial.println("START_RESET");
}
if(myGizwits.wifiHasBeenSet(WIFI_CON_ROUTER))
{
digitalWrite(8,LOW);
//Serial.println("Success_con_Router");
}
else if(myGizwits.wifiHasBeenSet(WIFI_AIRLINK))
{
digitalWrite(8,HIGH);
//Serial.println("IN_AIR_LINK");
}
bool varR_buer = 0;
if(myGizwits.hasBeenSet(EVENT_BUER))
{
myGizwits.read(EVENT_BUER,&varR_buer);//Address for storing data
digitalWrite(9,HIGH);//9号数字接口连接led灯测试是否接收到数据
//测试发现没有数据
delay(500);
digitalWrite(9,LOW);
delay(500);
if(varR_buer == 1)
{
// //测试发现没有数据
digitalWrite(9,HIGH);
delay(100);
digitalWrite(9,LOW);
delay(100);
digitalWrite(9,HIGH);
delay(100);
digitalWrite(9,LOW);
digitalWrite(9,HIGH);
delay(100);
digitalWrite(9,LOW);
delay(100);
digitalWrite(9,HIGH);
delay(100);
digitalWrite(9,LOW); digitalWrite(9,HIGH);
delay(100);
digitalWrite(9,LOW);
delay(100);
digitalWrite(9,HIGH);
delay(100);
digitalWrite(9,LOW);
delay(100);
}
else
{
//Serial.println("LED_OFF");
}
}
myGizwits.process();
}