智能灯 arduino总是报错

Chauncey_wang · 发表于 2017-12-10 15:05:32

我按照这篇文档做的《30分钟用arduino开发属于自己智能灯》，库文件都已经放在libiaries里面了，但是还是报错

我修改后的代码是这个

#include <Gizwits.h>

#include <Wire.h>

#include <SoftwareSerial.h>

#include <ChainableLED.h>

SoftwareSerial mySerial(A2, A3); // A2 -> RX, A3 -> TX

Gizwits myGizwits;

#define KEY1 6

#define KEY2 7

#define KEY1_SHORT_PRESS 1

#define KEY1_LONG_PRESS 2

#define KEY2_SHORT_PRESS 4

#define KEY2_LONG_PRESS 8

#define NO_KEY 0

#define KEY_LONG_TIMER 3

unsigned long Last_KeyTime = 0;

uint8_t Set_LedStatus = 0;

ChainableLED leds(A5,A4,1);

void LED_RGB_Control(byte red,byte green,byte blue)

{

leds.setColorRGB(0,red,green,blue);

}

unsigned long gokit_time_s(void)

{

return millis() / 1000;

}

char gokit_key1down(void)

{

unsigned long keep_time = 0;

if (digitalRead(KEY1) == LOW)

{

delay(100);

if (digitalRead(KEY1) == LOW)

{

keep_time = gokit_time_s();

while (digitalRead(KEY1) == LOW)

{

if ((gokit_time_s() - keep_time) > KEY_LONG_TIMER)

{

Last_KeyTime = gokit_time_s();

return KEY1_LONG_PRESS;

}

} //until open the key

if ((gokit_time_s() - Last_KeyTime) > KEY_LONG_TIMER)

{

return KEY1_SHORT_PRESS;

}

return 0;

}

return 0;

}

return 0;

}

char gokit_key2down(void)

{

int unsigned long keep_time = 0;

if (digitalRead(KEY2) == LOW)

{

delay(100);

if (digitalRead(KEY2) == LOW)

{

keep_time = gokit_time_s();

while (digitalRead(KEY2) == LOW) //until open the key

{

if ((gokit_time_s() - keep_time) > KEY_LONG_TIMER)

{

Last_KeyTime = gokit_time_s();

return KEY2_LONG_PRESS;

}

if ((gokit_time_s() - Last_KeyTime) > KEY_LONG_TIMER)

{

return KEY2_SHORT_PRESS;

}

return 0;

}

return 0;

}

return 0;

}

char gokit_keydown(void)

{

char ret = 0;

ret |= gokit_key2down();

ret |= gokit_key1down();

return ret;

}

/**

* KEY_Handle

* @param none

* @return none

*/

void KEY_Handle(void)

{

/* Press for over than 3 second is Long Press */

switch (gokit_keydown())

{

case KEY1_SHORT_PRESS:

mySerial.println(F("KEY1_SHORT_PRESS , Production Test Mode "));

myGizwits.setBindMode(WIFI_PRODUCTION_TEST);

break;

case KEY1_LONG_PRESS:

mySerial.println(F("KEY1_LONG_PRESS ,Wifi Reset"));

myGizwits.setBindMode(WIFI_RESET_MODE);

break;

case KEY2_SHORT_PRESS:

mySerial.println(F("KEY2_SHORT_PRESS Soft AP mode"));

myGizwits.setBindMode(WIFI_SOFTAP_MODE);

//Soft AP mode

break;

case KEY2_LONG_PRESS:

mySerial.println(F("KEY2_LONG_PRESS ,AirLink mode"));

myGizwits.setBindMode(WIFI_AIRLINK_MODE);

//AirLink mode

break;

default:

break;

}

/**

* Serial Init , Gizwits Init

* @param none

* @return none

*/

void setup() {

// put your setup code here, to run once:

mySerial.begin(115200);

leds.init();

digitalWrite(A0,HIGH);

pinMode(KEY1, INPUT_PULLUP);

pinMode(KEY2, INPUT_PULLUP);

pinMode(5,OUTPUT);

myGizwits.begin();

mySerial.println("GoKit init OK \n");

}

/**

* Wifi status printf

* @param none

* @return none

*/

void wifiStatusHandle()

{

if(myGizwits.wifiHasBeenSet(WIFI_SOFTAP))

{

mySerial.println(F("WIFI_SOFTAP!"));

}

if(myGizwits.wifiHasBeenSet(WIFI_AIRLINK))

{

mySerial.println(F("WIFI_AIRLINK!"));

}

if(myGizwits.wifiHasBeenSet(WIFI_STATION))

{

mySerial.println(F("WIFI_STATION!"));

}

if(myGizwits.wifiHasBeenSet(WIFI_CON_ROUTER))

{

mySerial.println(F("WIFI_CON_ROUTER!"));

}

if(myGizwits.wifiHasBeenSet(WIFI_DISCON_ROUTER))

{

mySerial.println(F("WIFI_DISCON_ROUTER!"));

}

if(myGizwits.wifiHasBeenSet(WIFI_CON_M2M))

{

mySerial.println(F("WIFI_CON_M2M!"));

}

if(myGizwits.wifiHasBeenSet(WIFI_DISCON_M2M))

{

mySerial.println(F("WIFI_DISCON_M2M!"));

}

/**

* Arduino loop

* @param none

* @return none

*/

void loop() {

KEY_Handle();//key handle , network configure

wifiStatusHandle();//WIFI Status Handle

bool varR_LED = 0;

if(myGizwits.hasBeenSet(EVENT_LED))

{

myGizwits.read(EVENT_LED,&varR_LED);//Address for storing data

if (varR_LED == 1)

{

LED_RGB_Control(200,0,0);

}

else

{

LED_RGB_Control(0,0,0);

}

myGizwits.process();

}

报错的信息是这个

Arduino:1.8.4 (Windows 8.1), 开发板："Arduino/Genuino Uno"

In file included from C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.c:16:0:

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.c: In function 'returnNtp2Wt':

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.h:67:23: warning: integer overflow in expression [-Woverflow]

#define DAY_SEC (24*60*60)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.c:246:21: note: in expansion of macro 'DAY_SEC'

if(utc >= x*DAY_SEC)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.h:67:23: warning: integer overflow in expression [-Woverflow]

#define DAY_SEC (24*60*60)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.c:248:22: note: in expansion of macro 'DAY_SEC'

utc -= x*DAY_SEC;

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.h:67:23: warning: integer overflow in expression [-Woverflow]

#define DAY_SEC (24*60*60)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.c:262:27: note: in expansion of macro 'DAY_SEC'

if(utc >= mons*DAY_SEC)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.h:67:23: warning: integer overflow in expression [-Woverflow]

#define DAY_SEC (24*60*60)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.c:264:28: note: in expansion of macro 'DAY_SEC'

utc -= mons*DAY_SEC;

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.h:67:23: warning: integer overflow in expression [-Woverflow]

#define DAY_SEC (24*60*60)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.c:277:19: note: in expansion of macro 'DAY_SEC'

if(utc >= DAY_SEC)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.h:67:23: warning: integer overflow in expression [-Woverflow]

#define DAY_SEC (24*60*60)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\common.c:279:20: note: in expansion of macro 'DAY_SEC'

utc -= DAY_SEC;

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\gizwits_protocol.c: In function 'gizwitsHandle':

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\gizwits_protocol.c:1243:13: warning: implicit declaration of function 'gizwitsEventProcess' [-Wimplicit-function-declaration]

gizwitsEventProcess(&gizwitsProtocol.issuedProcessEvent, (uint8_t *)&gizwitsProtocol.gizCurrentDataPoint, sizeof(dataPoint_t));

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:21:13: error: variable or field 'rb_new' declared void

void rb_new(RingBuffer* rb)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:21:13: error: 'RingBuffer' was not declared in this scope

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:21:25: error: 'rb' was not declared in this scope

void rb_new(RingBuffer* rb)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:34:15: error: variable or field 'rb_free' declared void

void rb_free(RingBuffer *rb)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:34:15: error: 'RingBuffer' was not declared in this scope

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:34:27: error: 'rb' was not declared in this scope

void rb_free(RingBuffer *rb)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:39:24: error: 'RingBuffer' was not declared in this scope

size_t rb_capacity(RingBuffer *rb)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:39:36: error: 'rb' was not declared in this scope

size_t rb_capacity(RingBuffer *rb)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:40:1: error: expected ',' or ';' before '{' token

{

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:44:24: error: 'RingBuffer' was not declared in this scope

size_t rb_can_read(RingBuffer *rb)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:44:36: error: 'rb' was not declared in this scope

size_t rb_can_read(RingBuffer *rb)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:45:1: error: expected ',' or ';' before '{' token

{

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:51:25: error: 'RingBuffer' was not declared in this scope

size_t rb_can_write(RingBuffer *rb)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:51:37: error: 'rb' was not declared in this scope

size_t rb_can_write(RingBuffer *rb)

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:52:1: error: expected ',' or ';' before '{' token

{

^

C:\Users\Administrator\Documents\Arduino\libraries\Gizwits\ringbuffer.cpp:57:20: error: 'RingBuffer' was not declared in this scope